The Stainless Steel Direct-Coupled Self-Priming Pump is one of the most widely used corrosion-resistant self-priming centrifugal pumps in China.
Most models adopt a direct motor-to-pump synchronous drive, in which the motor shaft is directly connected to the pump shaft. This configuration provides a compact design, small footprint, excellent self-priming performance, and easy maintenance.
These pumps are widely represented by major domestic series such as the ZX, GLF, ZXL, and JMZ models.
The pump casing is generally manufactured from high-quality stainless steel, including 304 stainless steel (1Cr18Ni9Ti), 316 stainless steel, and 316L stainless steel. The impeller is available in both semi-open and closed configurations to accommodate different types of pumped media.
Direct-coupled configuration
Bearing-bracket configuration
All models use cantilever-type mechanical seal technology for shaft sealing.
Mainstream products in this category can meet a wide range of industrial requirements, including the handling of clean liquids, corrosive liquids, and media containing small quantities of soft particles or fibrous materials.
1. Compact Design and Small Footprint
The pump adopts a direct-coupled synchronous drive, integrating the pump and motor into one compact unit.
Its streamlined design reduces the required installation area by approximately 30% compared with conventional self-priming pumps.
When equipped with an IP54 outdoor-duty motor, the pump can be installed outdoors without the need for a dedicated pump room.
2. Excellent Self-Priming Performance
The pump provides highly efficient self-priming performance.
Certain enhanced ZX models offer a self-priming height 1–2 m higher than that of conventional self-priming pumps and require less time to complete the self-priming process.
At a suction lift of 4 m, the self-priming time is approximately 20–40 seconds.
Before operation, it is only necessary to ensure that the pump casing contains the specified quantity of priming liquid.
3. High Efficiency and Energy Savings
The pump incorporates an optimized hydraulic model, achieving efficiency approximately 3%–5% higher than that of conventional self-priming pumps.
The impeller is dynamically balanced, ensuring smooth and vibration-free operation with low noise. This also helps extend bearing service life.
4. Stainless Steel Wetted Components with Excellent Corrosion Resistance
The wetted components and connecting bracket are manufactured from high-quality stainless steel. Available materials include 304, 316, and 316L stainless steel.
This configuration provides excellent wear resistance, reliable leak prevention, and extended service life.
5. Flexible and Customizable Material Options
If the pumped medium or operating conditions are not compatible with the standard configuration, alternative materials can be selected by agreement.
- 316L stainless steel.
- .
- This enables the pump to be adapted to a wider range of operating conditions.
6. Convenient Installation and Maintenance
A check valve is not required in the discharge line, and a foot valve is not required in the suction line.
This simplifies the piping system and improves installation, operation, and maintenance conditions.
The Stainless Steel Direct-Coupled Self-Priming Pump is suitable for a wide range of applications.
- 90℃ for direct-coupled models
- 105℃
The pump can handle liquids that contain or do not contain small soft particles or fibrous materials, as well as corrosive liquids and liquids requiring hygienic handling.
- Conveying corrosive media such as plating solutions, electrolytes, and textile-dyeing wastewater
- Industrial and municipal water supply and drainage, building fire-protection booster systems, and equipment cooling
- Farm irrigation, landscape irrigation, and municipal water-distribution systems
- Conveying pulp, black liquor, and various slurry-like process media
1. Design Standards
The pump is designed and manufactured in accordance with applicable company standards.
Production can also be organized in accordance with Chinese GB and HG standards, as well as relevant U.S. API standards, according to customer requirements.
2. Operating Principle
A liquid storage chamber is incorporated into the pump casing. The chamber communicates with the pump working chamber through a liquid-return passage at the top and a circulation passage at the bottom, forming an axial liquid-return, external-mixing self-priming system.
After the pump stops, a certain amount of liquid remains in the chamber.
When the pump starts, the impeller throws the stored liquid upward while entraining air. The liquid returns to the working chamber through the grid section of the gas-liquid separation pipe, while the air is discharged from the pump.
As a vacuum is gradually generated inside the pump, the pump achieves self-priming.
3. Construction
The pump is a horizontal, single-stage, single-suction centrifugal pump with a direct-coupled synchronous motor drive.
The impeller is available in either a semi-open or closed configuration.
When viewed from the motor end toward the pump, the pump rotates counterclockwise.
4. Shaft Sealing System
The pump uses a cantilever-type mechanical seal.
For special operating conditions, PTFE or other materials can be used for the stationary and rotating seal rings.
5. Materials of Wetted Components
The wetted components and connecting bracket are manufactured from 1Cr18Ni9Ti stainless steel (304 stainless steel).
- 316 stainless steel
- 316L stainless steel
6. Operating Conditions
|
|
|
|
|
3–800 m³/h |
|
|
12–80 m |
|
|
2,900 / 1,450 rpm |
|
|
<=90℃ for direct-coupled models; <=105℃ for bearing-bracket models |
|
|
<=1.6 MPa |
|
Self-priming height |
2–6.5 m |
|
|
<=100 cP |
|
|
Below 30% under suitable conditions |
7. Important Operating Precautions
a. Initial Priming
Before the first start-up, ensure that the pump casing contains the specified quantity of priming liquid.
Extended dry running is strictly prohibited.
b. Maximum Self-Priming Height and Suction-Line Length
The self-priming height must not exceed the specified value, generally 5–6.5 m.
The suction-line length should not exceed 10 m.
c. Suction-Line Installation
Minimize hydraulic losses in the suction line as much as possible.
The number of elbows in the suction piping should be minimized. A strainer is recommended at the pump suction inlet.
d. Ambient Conditions
The ambient temperature should not exceed 40℃.
The installation altitude should not exceed 1,000 m above sea level.
The relative humidity should not exceed 95%.
e. Abnormal Vibration or Noise
If abnormal vibration or unusual noise is detected during operation, stop the pump immediately and inspect it.
f. Cold-Weather Protection
If the pump will remain unused for an extended period during winter, drain all liquid from the pump casing to prevent damage caused by freezing.
8. General Performance Range
The general performance range is summarized below. Actual values vary according to the pump series and selected model.
|
|
|
|
|
|
3–800 m³/h |
|
|
|
12–80 m |
Certain series can reach 125 m |
|
|
1,450 / 2,900 rpm |
Direct-coupled models primarily use 2,900 rpm |
|
|
<=1.6 MPa |
|
|
|
<=90℃ for direct-coupled models; <=105℃ for bearing-bracket models |
Special series can reach 220℃ |
|
Self-priming height |
2–6.5 m |
Up to 6.5 m under clean-water conditions |
|
|
<=100 cP |
Solids concentration can be below 30% under suitable conditions |
|
|
25–300 mm |
Minimum nominal diameter: 25 mm; maximum: 300 mm |
|
|
0.55–132 kW |
|
|
|
2.0–6.0 m |
|
|
|
IP54 / IP55 |
IP54 is suitable for outdoor installation |
|
|

|
|
|
|
|
|
|
|
|
Self-Priming Height (m) |
|
|
25HBFX-8 |
2.3-5.5 |
9-3 |
0.25 |
2900 |
25 |
25 |
40 |
- |
4 |
|
25HBFX-13 |
3-10 |
16-4 |
0.55 |
2900 |
25 |
25 |
40 |
- |
5 |
|
40HBFX-18 |
6-18.5 |
21-8 |
1.5 |
2900 |
40 |
40 |
49 |
- |
5 |
|
50HBFX-22 |
8.5-23.8 |
28-14 |
3 |
2900 |
50 |
50 |
50 |
- |
4 |
|
25HYLZ-8 |
2.3-5.5 |
9-3 |
0.25 |
2900 |
25 |
25 |
40 |
- |
4 |
|
25HYLZ-13 |
3-10 |
16-4 |
0.55 |
2900 |
25 |
25 |
40 |
- |
5 |
|
40HYLZ-18 |
6-18.5 |
21-8 |
1.5 |
2900 |
40 |
40 |
49 |
- |
5 |
|
50HYLZ-22 |
8.5-23.8 |
28-14 |
3 |
2900 |
50 |
50 |
50 |
- |
5 |
|
25LQFZ-8 |
2.3-5.5 |
9-3 |
0.25 |
2900 |
25 |
25 |
40 |
- |
4 |
|
25LQFZ-13 |
3-10 |
16-4 |
0.55 |
2900 |
25 |
25 |
40 |
- |
5 |
|
40LQFZ-18 |
6-18.5 |
21-8 |
1.5 |
2900 |
40 |
40 |
49 |
- |
5 |
|
50LQFZ-22 |
8.5-23.8 |
28-14 |
3 |
2900 |
50 |
50 |
50 |
- |
5 |
|
25HBFX-8 (闭式) |
0.8-7.5 |
11-3 |
0.25 |
2800 |
25 |
20 |
43 |
- |
4.5 |
|
40HBFX-13 |
3.5-13 |
15-5 |
0.55 |
2800 |
40 |
25 |
50 |
- |
3.5 |
|
50HBFX-18 |
3-21 |
22-10 |
1.5 |
2800 |
50 |
40 |
52 |
- |
3.5 |
|
25ZX3.2-20 |
3.2 |
20 |
0.75 |
2900 |
25 |
25 |
- |
6.5 |
3.5 |
|
25ZX3.2-32 |
3.2 |
32 |
1.5 |
2900 |
25 |
25 |
- |
6.5 |
3.5 |
|
25ZXL3.2-20 |
3.2 |
20 |
0.75 |
2900 |
25 |
25 |
- |
6.5 |
- |
|
25ZXL3.2-32 |
3.2 |
32 |
1.5 |
2900 |
25 |
25 |
- |
6.5 |
- |
|
40ZX6.3-20 |
6.3 |
20 |
1.1 |
2900 |
40 |
40 |
- |
6.5 |
3.5 |
|
40ZX6.3-30 |
6.3 |
30 |
2.2 |
2900 |
40 |
40 |
- |
6.5 |
3.5 |
|
40ZXL6.3-20 |
6.3 |
20 |
1.1 |
2900 |
40 |
40 |
- |
6.5 |
- |
|
40ZXL6.3-30 |
6.3 |
30 |
2.2 |
2900 |
40 |
40 |
- |
6.5 |
- |
|
40ZXL10-32 |
10 |
32 |
4 |
2900 |
40 |
40 |
- |
6.5 |
- |
|
40ZXL12.5-50 |
12.5 |
50 |
5.5 |
2900 |
40 |
40 |
- |
6.5 |
- |
|
50ZX15-12 |
15 |
12 |
1.5 |
2900 |
50 |
50 |
- |
6.5 |
3.5 |
|
50ZXL15-12 |
15 |
12 |
1.5 |
2900 |
50 |
50 |
- |
6.5 |
- |
|
50ZXL12.5-32 |
12.5 |
32 |
4 |
2900 |
50 |
50 |
- |
6.5 |
- |
|
50ZXL12.5-50 |
12.5 |
50 |
7.5 |
2900 |
50 |
50 |
- |
6.5 |
- |
|
50ZXL20-75 |
20 |
75 |
11 |
2900 |
50 |
50 |
- |
6.5 |
- |
|
65ZX25-32 |
25 |
32 |
5.5 |
2900 |
65 |
65 |
- |
6 |
3.5 |
|
65ZXL25-32 |
25 |
32 |
5.5 |
2900 |
65 |
65 |
- |
6 |
- |
|
65ZXL25-50 |
25 |
50 |
7.5 |
2900 |
65 |
65 |
- |
6 |
- |
|
80ZX35-13 |
35 |
13 |
3 |
2900 |
80 |
80 |
- |
6 |
4 |
|
80ZX50-32 |
50 |
32 |
7.5 |
2900 |
80 |
80 |
- |
6 |
4 |
|
100ZX100-20 |
100 |
20 |
11 |
2900 |
100 |
100 |
- |
5.5 |
5 |
|
100ZXL100-30 |
100 |
30 |
15 |
2900 |
100 |
100 |
- |
5.5 |
- |
|
100ZXL100-40 |
100 |
40 |
18.5 |
2900 |
100 |
100 |
- |
6 |
- |
|
150ZXL170-45 |
170 |
45 |
37 |
2900 |
150 |
150 |
- |
6 |
- |
|
200ZXL400-32 |
400 |
32 |
55 |
1450 |
200 |
200 |
- |
5 |
- |
|
300ZXL600-32 |
600 |
32 |
90 |
1450 |
300 |
300 |
- |
5 |
- |
|
25ZWP8-15 |
8 |
15 |
2.2 |
2900 |
25 |
25 |
45 |
5.5 |
2 |
|
32ZWP5-20 |
5 |
20 |
2.2 |
2900 |
32 |
32 |
45 |
5.5 |
2.5 |
|
32ZWP10-20 |
10 |
20 |
2.2 |
2900 |
32 |
32 |
45 |
5.5 |
2.5 |
|
40ZWP10-20 |
10 |
20 |
2.2 |
2900 |
40 |
40 |
45 |
5.5 |
2.5 |
|
50ZWP15-30 |
15 |
30 |
3 |
2900 |
50 |
50 |
48 |
5.5 |
2.5 |
|
50ZWP20-35 |
20 |
35 |
5.5 |
2900 |
50 |
50 |
48 |
5.5 |
2.5 |
|
65ZWP25-30 |
25 |
30 |
5.5 |
2900 |
65 |
65 |
50 |
5.5 |
3 |
|
65ZWP25-40 |
25 |
40 |
7.5 |
2900 |
65 |
65 |
50 |
5.5 |
3 |
|
80ZWP40-25 |
40 |
25 |
7.5 |
1450 |
80 |
80 |
50 |
5.5 |
3 |
|
80ZWP50-60 |
50 |
60 |
22 |
2900 |
80 |
80 |
55 |
5 |
3 |
|
100ZWP100-15 |
100 |
15 |
7.5 |
1450 |
100 |
100 |
50 |
5.5 |
4 |
|
100ZWP80-20 |
80 |
20 |
7.5 |
1450 |
100 |
100 |
53 |
5.5 |
4 |
|
ZX32-25-160 |
3.2 |
32 |
1.5 |
2900 |
- |
- |
- |
5m/2min |
3.5 |
|
ZX40-32-200 |
6.3 |
50 |
3 |
2900 |
- |
- |
- |
5m/2min |
3.5 |
|
ZX50-50-160 |
12.5 |
32 |
3 |
2900 |
- |
- |
- |
5m/2.5min |
3.5 |
|
ZX50-50-200 |
12.5 |
50 |
5.5 |
2900 |
- |
- |
- |
5m/1.5min |
3.5 |
|
ZX65-50-160 |
25 |
32 |
5.5 |
2900 |
- |
- |
- |
5m/2min |
3.5 |
|
ZX80-65-200 |
60 |
55 |
18.5 |
2900 |
- |
- |
- |
5m/2min |
4 |
|
ZX80-65-250 |
60 |
75 |
22 |
2900 |
- |
- |
- |
5m/2.5min |
4 |
|
ZX100-80-160 |
100 |
32 |
15 |
2900 |
- |
- |
- |
5m/2min |
4.5 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
Популярни тагове: stainless steel direct-coupled self-priming pump, China stainless steel direct-coupled self-priming pump manufacturers, factory


